#Cost of weatherpro power awning manual

Have someone ready to help you in re-inserting the cotter pin while you hold the tubes still. Make sure to insert rubber tubes on the jaws of your vice grips or wrap it with rubber pieces so the tube's finish won't be scratched. Now that you are going to re-tension the spring, it's time to insert it back after you have reinstalled the torsion assembly.įirst, get a hold of the tube with the aid of a pair of vice grips. The cotter pins are the ones that lock the spring tension securely while taking down the RV awning. When you release the tension in the spring, the cotter pin that is inserted in the holes in the awning arms are removed. I hope you find the information here helpful on your next Weekend RV Adventure.Ĭlick here for some more information about me.Step 1 – Prepare to Re-insert the Cotter Pin Now I spend as many weekends as I can with my own family in our Cougar 5th wheel. I started camping with my parents when I was young and have been doing it ever since. The feeble retract side of the motor then typically has enough strength to roll the awning back out. Given all the comments on the forums regarding this power awning problem I just have to wonder why someone hasn’t taken Lippert to task and made them do the right thing.īy the way, with the extend side of the motor working fine you can roll the awning back, inside out, to get the thing secure for travel. One for units made before 2015 at $188 and one for units made after 2015 at $305.

Now doing a little more internet research I see eTrailer is listing two replacement motors. Checking battery voltage, voltage at the motor, trying with both the main and remote control, all ok. Spring 2020 and I decided to do a thorough troubleshooting exercise. Fast forward to fall 2019 and the blasted thing is doing the same thing again. I hounded Lippert with this information and they eventually “goodwilled” me a replacement. By late summer 2017 it would not retract, or at least needed help to do so. I have learned these motors have chronic problems.

Remove the ropes securing the awning arms.

Reconnect the wires and test the motor’s operation.

You may have to rotate the motor slightly to get the gears to line up and then rotate it back in place to line up the bolt holes.

Remove the bad motor and replace it with the new one.

Remove the 3 bolts that hold the motor in place using a 10mm wrench or socket.

Pull the wires up to access the quick disconnects and unplug the motor.

Remove the front and back covers from the motor on the right side of the awning.

This prevents the awning from unrolling completely when the motor is removed.

Tie the awning arms off to the bracket where it attaches to the side of your RV.

#Cost of weatherpro power awning manual

Use the manual override if the motor is completely dead. Tools Need: Philips Screw Driver, Ratchet with 10mm socket With Amazon Prime I was able to get the motor in 2 days and replacing the motor only take about 25 minutes. Here is a link if you need to order one Solara Power Awning Motor On Amazon. I purchased a replacement motor on Amazon for under $200. Step-by-step: Replacing the Motor on a Solara Power Awning If you get to this step you might have to get a dealer involved. If the motor checks out ok and bypassing the switch doesn’t make a difference you will have to try and trace the wires looking for any loose connections or broken wire. If the awning extends and retracts properly you need to replace the switch. Remove awning switch then, using a short piece of wire connect the 12V power terminal to the extend and then retract side of the switch. The next thing to check is the switch connections. If the awning moves correctly than the problem is in the wiring or switch. You can test the wiring by unplugging the awning motor and connecting wires directly to your battery or another 12V power source. It could also lead to an electrical fire. Try running the awning with the meter on the battery and disconnected from shore power, if there is a large drop in voltage your battery is bad.īad or loose wiring – A broken wire or loose electrical connection will prevent the awning from getting enough power to work properly. If you are plugged into shore power you should be getting over 12v. The easiest way to check your power is with the battery meter built in to your RV.įor a better check place a volt meter across your battery and see what it reads. Low 12v power – This could be caused by a bad battery or the 12v converter in your RV may have failed or be failing. Here are the items to check for power problems: If the awning motor doesn’t receive power, it will not be able to extend or retract your awning.